Mesa, AZ · ROC 334857 · ROC 334785 · Licensed, Bonded & Insured
Serving Customers in Mesa & Surrounding Areas
CALL OR TEXT

Published On: November 14, 2026 7 min read

Residential electrical panel with meter and labeled breakers

Short answer: A space heater keeps tripping the breaker because a standard 1,500 watt heater draws about 12.5 amps, which is most of what a 15 amp circuit can carry. Add a TV, lamps, or a second heater on the same circuit, or plug it into a power strip, and the breaker trips. The fix is to run the heater alone on its circuit, plug it directly into the wall, and call a licensed electrician if it still trips or the outlet feels warm. A room you heat with a space heater every winter often needs a dedicated circuit.

December and January bring out the space heaters across the East Valley. They go into home offices, garages, casitas, and add-on rooms that the heat pump never quite reaches. Then the breaker trips, or the outlet gets hot, and the question is whether it is the heater, the outlet, or the house. Here is how the numbers work, what usually causes it, and when a trip means it is time for an electrician.

The Math Behind the Trip

A common space heater is rated 1,500 watts. Divide watts by volts to get amps: 1,500 watts at 120 volts is about 12.5 amps. Most bedrooms, offices, and living rooms are on a 15 amp circuit. As general electrician guidance, a load that runs for hours, which a heater does, should stay around 80 percent of the breaker rating. On a 15 amp circuit that is about 12 amps. So one space heater, by itself, already uses nearly all of the circuit’s comfortable limit.

That is why the heater trips the breaker when you turn on a TV, a vacuum, or a hair dryer on the same circuit. It is not one thing failing. It is a circuit that is full. We are not giving you a fixed number of heaters per circuit, because it depends on what else is on that circuit and how the home was wired. An electrician can tell you what is actually connected.

Chart

Why one space heater can fill a 15 amp circuit

Circuit capacity compared with a common 1,500 watt heater, in watts.

A 15 amp, 120 volt circuit: breaker rating1,800 W
Continuous limit (80 percent, loads that run 3 hours or more)1,440 W (12 A)
One typical portable space heater on its highest setting1,500 W (12.5 A)

Reading it: one heater alone is already past the continuous limit, before a TV, a vacuum or anything else is plugged in on the same circuit.

Watts = volts x amps (15 A x 120 V = 1,800 W; 80 percent of that is 1,440 W; 1,500 W / 120 V = 12.5 A). Your circuit may be rated differently, and the breaker box shows each rating. Sources: UL Code Authority, Molded Case Circuit Breaker guide (a breaker is intended for no more than 80 percent of its rating when the load runs three hours or more); CPSC Staff Assessment on Portable Electric Heaters, February 2023 (22 of the 27 heaters staff tested were listed at 1,500 W, the most common maximum).

The Usual Causes

  • Sharing a circuit. A heater on the same circuit as a TV, lights, a computer, or a phone charger. This is the most common cause.
  • Two heaters on one circuit. Two heaters in the same room, or in two rooms that share a circuit, double the load.
  • An extension cord or power strip. These are not rated for a heater’s load, and the cord itself can run hot.
  • A worn or loose outlet. A plug that fits loosely, or an outlet with weak contacts, creates resistance and heat.
  • A weak or aging breaker. Breakers can wear out and trip under a load they used to carry.
  • Aluminum wiring in an older home. Some older Mesa and Tempe homes have aluminum branch wiring, and the connections can loosen with heat and time.
  • The heater itself. A damaged cord, a failing element, or a unit that overheats can trip a breaker on its own.
Older electrical panel with handwritten labels and spare breaker spaces on a Mesa area home
An older panel with handwritten labels. Panels like this are common in East Valley homes.

What Is Safe to Try

These steps are safe for a homeowner and often solve the problem:

  • Plug the heater directly into a wall outlet, not a power strip or an extension cord.
  • Turn off other things on the same circuit while the heater runs, or move the heater to a room on a different circuit.
  • Run only one heater per circuit.
  • Inspect the heater’s cord and plug. Throw the heater away if the cord is cracked or the plug is scorched.
  • Turn the breaker fully off and then on to reset it. Do it once. If it trips again, stop.

Do not remove the outlet cover or the panel cover to investigate, and never replace a breaker with a larger one to stop the tripping. A larger breaker on the same wire is a fire risk, because the wire can overheat before the breaker ever trips. That is a job for a licensed electrician.

When to Stop and Call an Electrician

Call right away if the outlet or the plug feels warm or hot, if you see discoloration or scorch marks, if you smell burning plastic, if you hear buzzing or crackling, or if the breaker trips every time you use the heater. Heat at an outlet means a connection is failing, and that is how electrical fires start. Stop using that outlet and turn off its breaker if you can do it safely. Our electrical repair and troubleshooting team handles tripping breakers, worn outlets, and overloaded circuits, and our outlet and switch service covers replacing worn receptacles. If you see other warning signs around the house, read our guide to the signs you need an electrical panel upgrade.

Chart

Space heaters and home heating fires

Space heaters cause about a third of heating fires, but most of the injuries and deaths. That is why a hot plug or outlet is worth a call.

Share of home heating fires33%
Share of injuries in those fires80%
Share of deaths in those fires88%

Fixed and portable space heaters, as a share of all home heating equipment fires (non-confined fires), annual averages for 2016 to 2020, the latest NFPA edition we verified. Source: NFPA, Home Heating Fires (R. Campbell, December 2022).

The Long-Term Fix: A Dedicated Circuit

If you run a space heater in the same room every winter, the right fix is usually a dedicated 20 amp circuit that serves only that room’s heater or load. A licensed electrician can run a new circuit, add a properly rated outlet, and confirm your panel has room for it. If the panel is full, the electrician will tell you what the options are.

Wall mounted mini split indoor head in a living room installed by JBee Industries
A wall mounted mini split heats and cools one room without a space heater.

It is also worth asking why the room needs a space heater at all. A garage, casita, or addition that the heat pump never warms is often better served by a ductless system. A mini split heats and cools a single room efficiently, and it is a permanent answer where a space heater is only a patch.

Frequently asked questions

Why does my space heater keep tripping the breaker?

A typical 1,500 watt space heater uses most of a standard 15 amp circuit by itself. If anything else shares that circuit, such as a TV, lamps, or a computer, the total goes past what the breaker allows and it trips. A worn outlet, a loose connection, or a power strip or extension cord can also cause it.

How many space heaters can I run on one circuit?

For most bedrooms and offices, one at a time and nothing else heavy on the circuit. Electricians generally keep a continuous load to about 80 percent of the breaker rating, and a 1,500 watt heater is close to that limit on a 15 amp circuit. An electrician can tell you what is on your circuit and what it can handle.

Will a 1,500 watt space heater trip a breaker?

It can. A 1,500 watt heater draws about 12.5 amps at 120 volts. On a 15 amp circuit that already powers other things, it often trips. On a circuit with nothing else running, it may hold, but it will run near the limit.

Can I plug a space heater into a power strip or extension cord?

No. Plug a space heater directly into a wall outlet. Power strips and most extension cords are not built for a heater’s continuous load, and they can overheat and start a fire.

Should I put in a bigger breaker if the heater keeps tripping it?

Never. The breaker protects the wire in the wall. A larger breaker on the same wire lets the wire overheat before the breaker trips, which is a fire risk. If the circuit needs more capacity, a licensed electrician should add a dedicated circuit.

Need an Electrician in Mesa, Gilbert, or Chandler?

JBee Industries is a licensed, family owned electrical and HVAC contractor based in Mesa. We serve Mesa, Gilbert, Chandler, Tempe, Queen Creek, San Tan Valley, Phoenix, Scottsdale, and Paradise Valley. If a space heater keeps tripping your breaker, call or text (480) 618-6969 or contact us online. We will find out why, explain what we see, and tell you whether you need a repair, a new outlet, or a dedicated circuit.

What JBEE customers say

Jorge and his team arrived to upgrade my electrical panel from a 20 breaker space to a 40 breaker space as well as electrical for a hot tub. ... They were professional and got the job done in a timely manner. I will definitely be using them again!
Andrew Garcia Google review, October 2025

Read all reviews on Google

Get a free estimate today

Call or text JBEE Industries, or send the form and we will get back to you.

Call (480) 618-6969

Leave a Reply

Your email address will not be published. Required fields are marked *

Get Your Free Estimate