Mesa, AZ · ROC 334857 · ROC 334785 · Licensed, Bonded & Insured
Serving Customers in Mesa & Surrounding Areas
CALL OR TEXT
Fans and lighting
Quiet Fans.
Better Light.

Ceiling Fan Installation and Lighting in Mesa, AZ

JBEE Industries provides ceiling fan installation and lighting installation for Mesa homes, from swapping a dated fixture for a fan to wiring a new fan where no light ever hung. Our licensed electricians mount every fan on a fan rated box braced to the framing, set the right downrod, balance the blades and match LED fixtures to compatible dimmers. You approve a written price first, and one visit can cover several rooms. We work in Gilbert, Chandler, Tempe and across the East Valley too.
Every fan we hang gets
01
A box rated and braced for a moving load
02
A downrod matched to your ceiling height
03
Balanced blades so it runs without wobble
04
Wall, remote or smart control, your call
Several rooms on the list?
Group the fans and fixtures into one visit and we plan the wiring for all of them together.
★  5.0 ★ Google Rating
★  ROC 334857 & 334785
★  Rebate Efficiency Arizona Contractor
★  $0 Free Estimates
●  Mesa
●  Gilbert
●  Chandler
●  Tempe
●  Queen Creek
●  San Tan Valley
●  Scottsdale
●  Gold Canyon
●  Phoenix
★  5.0 ★ Google Rating
★  ROC 334857 & 334785
★  Rebate Efficiency Arizona Contractor
★  $0 Free Estimates
●  Mesa
●  Gilbert
●  Chandler
●  Tempe
●  Queen Creek
●  San Tan Valley
●  Scottsdale
●  Gold Canyon
●  Phoenix
Fans that stay put

A Ceiling Fan Is Only as Solid as the Box Above It

A ceiling fan weighs more than most light fixtures, and it twists and vibrates every minute it runs. Plenty of Mesa homes have a plastic or pancake box meant only for a light, and a fan hung from one tends to wobble, click and loosen until it is a hazard over the bed.
We open the ceiling, check what the fan will hang from, and install a box listed for fan support with a brace across the joists when needed. Then the blades get balanced, the canopy gets tightened, and the fan and light are wired to the controls you want.
What we look at above the ceiling
01
Box type, rating and how it is fastened
02
Joist spacing and bracing options
03
Wire condition and the circuit feeding it
04
Attic access for running a new switch leg
Comfort in a Mesa summer

Let Ceiling Fans Take Some Load Off the Air Conditioner

A fan does not lower the room temperature, but moving air across your skin makes 80 degrees feel closer to 76. That lets many households nudge the thermostat up a few degrees from June through September without feeling it, which means fewer hours of compressor run time on your SRP or APS bill.
Set the blades to turn counterclockwise in summer so air pushes down, and shut fans off in empty rooms because they cool people, not furniture. If the house still runs hot with every fan going, the air conditioner may need attention, and our HVAC team can check it on the same account.
Sizing a fan to the room
01
Small bedrooms and offices get a compact span
02
Living rooms need a wider span to move air
03
Blades sit at least 7 feet above the floor
04
High ceilings get a longer downrod
Time for a new fan or fixture?

Signs Your Fans and Lights Need an Electrician

Some of these are about comfort and some are about safety. We rank them so you know which to fix first.
Stop using it
Fan wobbles and keeps loosening
The box or mount is likely not rated for a fan. Switch it off until it is checked and resecured.
Stop using it
Fixture or canopy too hot to touch
Bulbs above the fixture rating or a burned connection inside. Turn it off at the wall.
Fix it soon
Lights flicker on a dimmer
An old dimmer driving new LEDs. Not dangerous on its own, but the hum and flicker get worse.
Fix it soon
Fan hums, rattles or grinds
Worn bearings, a bad capacitor in the motor or loose blade irons. Often cheaper to replace than repair.
Worth an upgrade
Rooms still hot with fans running
Fans help, but they cannot make up for an air conditioner that is losing capacity.
Worth an upgrade
Dim, dated fixtures throughout
LED fixtures use a fraction of the power of old incandescent and halogen lights.
How a fan or lighting job works

From Your Room List to Fans Spinning Smoothly

01

List the rooms

Tell us which fans and fixtures you want, and whether you already bought them.
02

Check the ceilings

We confirm boxes, wiring and attic access, then price the whole list in writing.
03

Mount and wire

Fans go up on rated boxes, fixtures get matched dimmers, and new switch legs run where needed.
04

Balance and walk through

Every fan is balanced and tested at each speed, and we show you the controls.
Lighting that works the way you want

LED Fixtures, Recessed Lights and Dimmers That Do Not Flicker

Swapping old fixtures for LED cuts power use and bulb changes, but the upgrade can go wrong when a new fixture lands on an old dimmer. Dimmers designed for incandescent loads make LEDs flicker, hum or refuse to dim smoothly.
We pair each fixture with a dimmer or smart switch listed for its load, and plan kitchen, living room and bedroom lighting together with the fans so the switches end up where people reach for them. If we open a box and find scorched or brittle wire, we tell you and quote the fix before anything else goes in.
Before we hang a single fixture
01
Confirm the fixture weight the box can hold
02
Check for a neutral in the switch box
03
Match the dimmer to the LED driver
04
Agree on switch locations room by room
FAQ

Ceiling Fan and Lighting Questions We Get in Mesa

Usually. The box in the ceiling has to be listed for fan support, so we check it and replace it with a braced fan box when the existing one is only rated for a light.

Yes. We run new cable from a nearby circuit, install a fan rated box and add a wall switch or control. Attic access above the room makes it simpler, and we tell you during the estimate how we plan to get there.

Counterclockwise when you look up at it, so air is pushed down toward you. A small switch on the motor housing or a button on the remote reverses it.

Not normally. A fan draws little power and can share a lighting circuit. It needs its own run only when there is no wiring nearby or the existing circuit is already loaded, and we check that first.

Most often an older dimmer built for incandescent bulbs is driving them. Swapping in an LED rated dimmer and using dimmable bulbs fixes it in most homes.

Yes, with a sloped ceiling adapter and a downrod long enough to keep the blades clear of the slope. We size it so the fan sits where it can move air.

Yes. A covered patio needs a damp or wet rated fan depending on how exposed it is to monsoon rain, with weather resistant connections and controls. Call (480) 618-6969 to plan it.

It is live wiring and an overhead load, and a loose splice in the ceiling can heat up for months where nobody sees it. A licensed electrician also checks the box and circuit that a quick swap skips.

Most often an older dimmer built for incandescent bulbs is driving them. Swapping in an LED rated dimmer and using dimmable bulbs fixes it in most homes.

Yes, with a sloped ceiling adapter and a downrod long enough to keep the blades clear of the slope. We size it so the fan sits where it can move air.

Yes. A covered patio needs a damp or wet rated fan depending on how exposed it is to monsoon rain, with weather resistant connections and controls. Call (480) 618-6969 to plan it.

It is live wiring and an overhead load, and a loose splice in the ceiling can heat up for months where nobody sees it. A licensed electrician also checks the box and circuit that a quick swap skips.

Ready for fans that work?

Get Your Fans and Fixtures Installed Right

Send the form with the rooms and the fans or fixtures you want, or call (480) 618-6969. A licensed electrician confirms the boxes and wiring, then gives you a free estimate for the whole list so it can all be done in one visit.
Mesa
Scottsdale
Gold Canyon
Phoenix

Request a Fan or Lighting Estimate

List the rooms and how many fans or fixtures.
Get Your Free Estimate