Mesa, AZ · ROC 334857 · ROC 334785 · Licensed, Bonded & Insured
Serving Customers in Mesa & Surrounding Areas
CALL OR TEXT
Panel and service upgrades
More Power.
Fewer Tripped Breakers.

Electric Panel Upgrade in Mesa, AZ

JBEE Industries handles electrical panel upgrades in Mesa for homes that have outgrown their breaker panel or their 100 amp service. A licensed electrician runs a load calculation, then replaces worn, crowded or recalled panels and upgrades service to 200 amps when your AC, EV charger, solar or heat pump needs it. We coordinate the disconnect and reconnect with SRP or APS, pull the permit and give you a written price first, with financing options available. Gilbert, Chandler and Queen Creek homeowners call us too.
Utility service mast with overhead wires on a shingle roof
Load calculation first
You see the numbers behind our recommendation, not a guess about what your house needs.
★  5.0 ★ Google Rating
★  ROC 334857 & 334785
★  Rebate Efficiency Arizona Contractor
★  $0 Free Estimates
●  Mesa
●  Gilbert
●  Chandler
●  Tempe
●  Queen Creek
●  San Tan Valley
●  Scottsdale
●  Gold Canyon
●  Phoenix
★  5.0 ★ Google Rating
★  ROC 334857 & 334785
★  Rebate Efficiency Arizona Contractor
★  $0 Free Estimates
●  Mesa
●  Gilbert
●  Chandler
●  Tempe
●  Queen Creek
●  San Tan Valley
●  Scottsdale
●  Gold Canyon
●  Phoenix
When the panel is the bottleneck

Your Home Grew. The Panel Behind It Did Not.

Many East Valley homes still run on a panel sized for one air conditioner, a gas range and a few lamps. Add a second AC system, a pool pump, a home office and an electric vehicle, and the same panel ends up tripping breakers, filled with tandem breakers and running warm in the July sun.
A new panel gives every circuit a properly rated breaker, clean bus connections and room for what is coming next. When the service itself is too small, we raise it to 200 amps so the house can actually draw the power it needs.
What a load calculation counts
01
Square footage and general lighting load
02
Every AC, heat pump, pool and spa motor
03
Ranges, dryers, water heaters and EV chargers
04
Equipment on your wish list for later
Panels worth replacing

Old, Overheating or Recalled Panels Should Not Wait

Some panels are a problem no matter how much capacity they have. Federal Pacific Stab-Lok and Zinsco panels have a long history of breakers that fail to trip, and many electricians recommend replacing them on sight. Fuse boxes, rusted enclosures and panels with scorched bus bars belong in the same group.
Arizona heat makes a tired panel worse. Exterior panels on south and west walls can bake well past the air temperature, and aluminum terminations and older breakers loosen with every hot afternoon and cool night. We look inside, not just at the label, before recommending anything.
Red flags we find inside panels
01
Breakers that do not match the panel brand
02
Two wires under a single breaker screw
03
Heat discoloration on the bus or lugs
04
Missing grounding and bonding connections
Is your panel struggling?

When Does a Mesa Home Need a New Electrical Panel?

Some signs mean the panel is unsafe today. Others mean it will not handle what you plan to add. We sort them by urgency.
Call us today
Panel feels hot or smells burnt
Heat at the cover usually means a loose lug or a failing breaker. Keep everyone away and call.
Call us today
Breakers will not stay reset
A breaker that trips at once or crackles when you flip it needs testing before you use that circuit again.
Plan the upgrade
Flicker every time cooling starts
Deep dips each cycle point to undersized service, a loose connection, or a hard starting compressor.
Plan the upgrade
Federal Pacific or Zinsco label
These panels have a record of breakers that do not trip on overload. Replacement is the usual advice.
Plan the upgrade
Every slot is already full
Tandem breakers and piggybacked wires are a sign the panel ran out of room years ago.
Upgrade before adding
Big electric loads on the way
Upgrade the panel first so the new equipment is not squeezed onto an overloaded service.
Panel or service

Panel Replacement or a Full Service Upgrade?

Panel replacement

Service upgrade

A load calculation tells us which one your home needs, and sometimes a subpanel covers it.
How a panel upgrade runs

From Load Calculation to a Labeled, Inspected Panel

01

Load calculation

We add up what your home uses now and what you plan to add, then recommend a size.
02

Written price and permit

You approve the scope and price, and we file the permit and schedule the utility.
03

Swap day

Power goes off while licensed electricians replace the panel and land every circuit on new breakers.
04

Inspection and labels

The city inspects the work, power is restored, and every breaker is labeled clearly.
Plan the panel once

Sizing for Solar, Batteries, Heat Pumps and the Next EV

How much solar you can tie in depends partly on your busbar and main breaker ratings, so the panel is part of every solar design. Swapping gas appliances for a heat pump, an induction range or a heat pump water heater adds load the same way.
Because JBEE installs solar, Tesla Powerwall systems and HVAC equipment, we size the panel for all of it in one plan rather than paying for panel work twice. A new panel is also the natural time to add whole home surge protection, which current code calls for on many service replacements.
Upcoming loads to tell us about
01
Solar panels now or within a few years
02
A Tesla Powerwall or other home battery
03
Retiring gas appliances for electric ones
04
A second EV or a workshop in the garage
FAQ

Electrical Panel Upgrade Questions From Mesa Homeowners

Frequent trips, lights that dip as the AC starts, a warm or buzzing cover, rust or no empty breaker spaces are the usual clues. Plans for an EV charger, solar or a large electric appliance are another reason. Running the numbers on your actual load gives a firm answer.

It can be for a smaller home with gas appliances and one air conditioner. Two AC units, a pool, an EV charger or an electric range usually push it past its limit. We calculate your actual load before recommending a bigger service.

Most electricians recommend it. Both brands have a documented history of breakers that may not trip when they should, and replacement breakers are hard to find. We can inspect yours and price a new panel.

The house is without power while the panel is swapped, and how long depends on the scope of the job. A service upgrade also depends on the SRP or APS disconnect and reconnect, and we give you the schedule before work starts.

Yes. Panel replacements and service upgrades need an electrical permit and a city inspection. We pull the permit as part of the job and schedule the inspection.

Sometimes. The busbar and main breaker ratings limit how much solar can connect. Our team designs the solar system and the panel together so the numbers work.

Yes. Larger panel and service jobs can be financed. Call (480) 618-6969 for a free estimate and ask about financing at the same time.

Yes. Panel replacements and service upgrades need an electrical permit and a city inspection. We pull the permit as part of the job and schedule the inspection.

Sometimes. The busbar and main breaker ratings limit how much solar can connect. Our team designs the solar system and the panel together so the numbers work.

Yes. Larger panel and service jobs can be financed. Call (480) 618-6969 for a free estimate and ask about financing at the same time.

Panel at its limit?

Find Out What Your Panel Can Handle

Call (480) 618-6969 or send the form with your panel brand and amp rating if you know them, plus anything you plan to add. A licensed electrician runs the load calculation and gives you a free, written estimate.
Mesa
Scottsdale
Gold Canyon
Phoenix

Request a Panel Upgrade Estimate

Tell us what you plan to add: EV, solar, AC.
Get Your Free Estimate